Contact us
- : 0086-371-86151627 0086-371-86151827
- : 0086-371-86011881
- : [email protected]
- : [email protected]
- : bebonchina
Products- Boiler steels
- High carbon steel
- High Yield steel
- steel for welded tubes
- General construction steel
- steel with Cr.,Mo.,Cr-Mo
- Steel for large diameter pipes
- Simple pressure vessels steel
- Steel for gas cylinders and gas vessels
- General purpose structural steels
- Steel for boilers and pressure vessels
- steel resistant to atmospherical corrosion
- Carbon steel and low alloy steel
- Fine-grain structural steels,normalised rolled
- weldable normalized fine grained pressure vessel steels
Introduction to S460M steel plate
S460M plate is a European standard low-alloy steel plate, thermomechanically rolled and weldable fine-grained structural steel. S460M steel can be used for load-bearing parts of bridges, sluices, storage tanks, water supply tanks, etc. and low-temperature welded structures.
s460m steel plate technical standard: EN10025.
S460M steel plate heat treatment (delivery status): hot rolled.
Mechanical properties of S460M steel plate:
| Thickness | Mechanical properties | ||
| ≤16mm | ReH(MPa) | ≥460 | When the yield is not obvious, use Rp0.2 |
| Rm(MPa) | 540-720 | ||
| A(%) | ≥17 | Horizontal | |
| Impact temperature | -20 | ||
| Akv(J) | ≥40 | Vertical; Horizontal: Akv≥20J | |
| Remark | Tensile test transverse sampling | ||
| >16-40mm | ReH(MPa) | ≥440 | When the yield is not obvious, use Rp0.2 |
| Rm(MPa) | 540-720 | ||
| A(%) | ≥17 | Horizontal | |
| Impact temperature | -20 | ||
| Akv(J) | ≥40 | Vertical; Horizontal: Akv≥20J | |
| Remark | Tensile test transverse sampling | ||
| >40-63 | ReH(MPa) | ≥430 | When the yield is not obvious, use Rp0.2 |
| Rm(MPa) | 530-710 | ||
| A(%) | ≥17 | Horizontal | |
| Impact temperature | -20 | ||
| Akv(J) | ≥40 | Vertical; Horizontal: Akv≥20J | |
| Remark | Tensile test transverse sampling | ||
| >63-80mm | ReH(MPa) | ≥410 | When the yield is not obvious, use Rp0.2 |
| Rm(MPa) | 510-690 | ||
| A(%) | ≥17 | Horizontal | |
| Impact temperature | -20 | ||
| Akv(J) | ≥40 | Vertical; Horizontal: Akv≥20J | |
| Remark | Tensile test transverse sampling | ||
| >80-100mm | ReH(MPa) | ≥400 | When the yield is not obvious, use Rp0.2 |
| Rm(MPa) | 500-680 | ||
| A(%) | ≥17 | Horizontal | |
| Impact temperature | -20 | ||
| Akv(J) | ≥40 | Vertical; Horizontal: Akv≥20J | |
| Remark | Tensile test transverse sampling | ||
S460M plate finished product melting analysis, chemical composition, chemical elements:
| C | Si | Mn | P | S | Ni | Cr | Mo | Cu | Nb | V | Ti | Als | N |
| ≤0.16 | ≤0.6 | ≤1.7 | ≤0.03 | ≤0.025 | ≤0.8 | ≤0.3 | ≤0.2 | ≤0.55 | ≤0.05 | ≤0.12 | ≤0.05 | ≥0.015 | ≤0.025 |
Remarks on ingredients: When other nitrogen-fixing elements are contained, the lower limit of Als content does not apply; the maximum C content can be 0.18.